Showing 13–24 of 28 results

Ring Latch

£5.00 inc VAT

Perfect for Garden Gates

A popular product on any garden gate the ring latch allows easy use from either side of a fully board gate. Easy to fit and sturdy in construction this ring latch suits gates that are 80-85mm thick. Please note you will need a 10mm wooden drill bit to fit this to your gate.

It comes fully galvanised to help achieve a long life span with protection against rot and rusting.

Bottom Band

£5.00 inc VAT

Similar in construction to the Top Band this product is mainly used for either much smaller gates as an alternative to the top band or in replacement of an adjustable gate eye at the bottom of the gate. It suits a 19mm gate hook.

Commonly used on garden gates, or in areas where small gates are required. This is an easy to fit and use and comes pre-drilled for one 10mm cup head square bolt which is provided free of charge. It also has a predrilled hole for an additional screw if you choose to use this. You will have to drill your gate style so you will need a 10mm wood drill bit, which we can provide if required.

Drop Over Frame (No Handle) 14″

£5.00 inc VAT

Light Drop Over Frame For Shorter Gates

This is a lighter weight product than the drop over frame with handle and is predominately used by the gardener and landscaper for small shorter gates that need a lighter drop over frame.

One massive benefit to this drop over frame is that without the handle it has a much sleeker looker on the gate once closed, for this reason it is popular with more modern gate ways and those not wanting ironmongery to be seen.

Monkey Tail Bolt

£6.50 inc VAT

The Monkey Tail Bolt is traditionally used on garage doors, but over time has been used for other purposes such as large garden shed doors and animal stabling.

Overall this bolt measures 600mm long and sits on a 50mm wide plate, which comes predrilled for screws. It is also galvanised to stop rusting and rotting. When fully pushed up or down the Monkey Tails bolt sticks out approximately 80mm, give ample length to secure the door or gate. Its common place to have two of these on one gate, one facing upwards and the other facing down.

Adjustable Bottom Eye & Clips

£7.00 inc VAT

Commonly used on the bottom of wooden gates, the adjustable gate eye allows you to adjust the level and swing elevation of your gate. This is useful as over time gates tend to relax and drop, this means the shutting end of the gate tends to get lower. By adjusting the two heavy duty 20mm nuts you can level the gate up.

The adjustable eye comes as standard in a our full gate hanging kits but its great for adjustability if required just on its own. Some of our customers use two of these on home made gates and doors to allow for great adjustment over time.

4 Hole Hook On Plate

£7.50 inc VAT

Heavy Duty Gate Hanging Hooks

This is a standard product for all landscapers, small holders, contractors and farmers. The four hole hook on plate is normally used on square gate posts as the four fixing points and large back plate give a sturdy and strong backing to hang any gate from 600mm to 4800mm.

The hook on plate is easy to fix and we recommend using 100mm coach screws complete with washers.

2 Hole Hook On Plate

£7.50 inc VAT

Heavy Duty Gate Hanging Hooks

These hooks are used by everyone from the expert fencing contractor to the normal DIY-er.  Typically these hooks are used to hang garden gates and decorative gates which need a little more support from a heavy fixing. They are a good match if you currently have some ironmongery and need to match hooks to it.

The two hole hook on plate is most commonly used on round gate posts as it sits and fixes nicely in to the circular face. For square gate posts please see the four hole hook on plate which may be more suitable.

Hunting Latch

£8.00 inc VAT

Typically used on gates that need to be access from horseback, these are traditionally used on hunting routes. They are most popular nowadays for gates on to or from riding arenas. They are excellent for allowing gates to swing a full 180 degrees from the hang post. Please note that these fittings are stiff to start off with as they are sprung mild steel.

It comes with as standard a fitting that allows only 90 degrees access from the post but an additional part can be added to allow 180 degree access. Please see the ‘hunting latch clip’ below in the related products.

 

Drop Over Frame (with handle) 14″

£8.00 inc VAT

This is our most popular drop over frame.

Its strong construction made out of 4mm thick mild steel which provides a real heavy duty drop over frame.

It is used when two gates are used as a pair that shut together, the drop over frame stops the gates from moving and twisting over time by securing them together. Its a must for all double gate openings.

It neatly hinges on one gate (usually the larger) to fold over the other. If the two gates are the same length it doesn’t matter which side it goes on. When you need to open the gates it rotates all the way back over and on to the gate it is hinged on.

 

 

Lockable Drop Bolt (24″)

£9.00 inc VAT

The lockable drop bolt is perfect for gateways that are either away from your property or you need additional security at certain times. They are popular with home owners on their drive ways so these gates can be locked shut during work hours or holidays, giving you some additional peace of mind.

Easy to fit they come complete with fittings to suit a 60mm thick gate, if your gate is thicker than this please inform us during the purchase of this product. If you buy this lockable drop bolt and one of our gates we will automatically send you fittings to suit.